Open the battery cover, then fit the same battery type your HP mouse already uses, usually one AA battery, with the polarity marks lined up. Skip that check, or install a weak cell, and the mouse can stay dead while you chase the receiver or switch for no reason. This guide shows how to change the battery in common HP wireless mouse models and how to separate a battery fault from a receiver or contact issue.

Identify your HP mouse model

Find the exact model number on the bottom label before you buy or install anything. HP wireless mice are not all wired the same inside: z3700, x3000, x4000, HP Wireless Mouse 200, and HP Comfort Grip Wireless Mouse can use different battery sizes and compartment styles.

If the mouse still has power, look for the model name near the product label or inside the battery bay.

What you'll need

  • The correct replacement battery or batteries for your exact HP mouse model
  • A clean, dry work surface
  • A fingernail or a thin plastic pry tool for tight covers
  • A fresh USB port for the nano receiver if you need to reconnect it

HP mouse battery quick-reference table

HP mouse model Likely battery size Compartment style First two checks if it still fails
HP Wireless Mouse 200 1 AA Bottom shell cover Reinsert the USB nano receiver; check battery contact springs
HP z3700 1 AA on many versions; some compact variants use 1 AAA Top shell or bottom door, depending on version Power cycle the mouse; inspect polarity marks and the contacts
HP x3000 1 AA Bottom cover Check that the receiver stays plugged in; confirm the battery is seated against the springs
HP x4000 1 AA Removable shell or sliding door Reinsert the receiver; look for bent or dirty contacts
HP Comfort Grip Wireless Mouse 1 AA or 2 AAA, depending on revision Bottom shell with internal tray Check the polarity marks; power cycle and reconnect the receiver

How do you open the battery compartment?

How do you open the battery compartment?
Wireless mouse underside showing the battery compartment and power switch

Turn the power switch off first, then open the cover by matching the compartment style on your model. HP mice usually use a slide door, a snap cover, or a removable top shell, and some compact models hide a small battery ribbon inside the bay.

  1. Slide the power switch to Off.
  2. Flip the mouse over and find the battery door seam, tab, or shell release.
  3. Slide the door in the direction of its arrow, or lift the top shell where the release tab sits.
  4. If the compartment feels tight, press the release area while lifting gently; do not pry hard enough to bend the plastic.

Suppose a z3700 has a tight top shell and no obvious tab. Press near the rear edge, then lift just enough to clear the clip. Forced twisting can crack the latch and leave the cover loose.

How do you change the battery?

How do you change the battery?
Wireless mouse underside showing battery compartment and power switch

Remove the old battery, check the polarity marks, and install the new cell the same way it came out. Many HP mice use a single AA battery, while some compact versions use AAA cells or two cells, so the positive and negative ends must match the printed symbols inside the bay.

  1. Take out the old battery by lifting it from the spring side first.
  2. Check the plus and minus marks inside the compartment before inserting the new cell.
  3. Seat the battery so each end presses firmly against the contact springs.
  4. If your mouse uses two cells, match both positions before closing the cover.
  5. Close the compartment, then move the power switch back to On.

A common first-timer mistake is putting the battery in one notch off; the mouse then stays dark even though the cell is new.

Why is your HP wireless mouse still not working?

Why is your HP wireless mouse still not working?
Underside of a wireless mouse with its battery compartment open

If the pointer still stays dead after replacement, the battery may not be the problem. The USB nano receiver, the battery contacts, or the pairing state can stop the mouse from responding even with a fresh cell installed.

  1. Unplug the USB nano receiver, wait 10 seconds, and plug it back into the same PC.
  2. Slide the mouse power switch Off, wait 10 seconds, then switch it On again.
  3. Check the battery contact springs for dirt, bending, or weak pressure against the battery ends.
  4. If the model has a battery ribbon, make sure it is not trapped under the cell or folded away from the pull tab.
  5. Try a different USB port if the receiver LED or pairing response still fails.

Picture an x3000 that has a fresh AA cell but no cursor movement. If the receiver was bumped loose from the USB port, the mouse can look “dead” even though power is present. Reinsert the receiver before assuming the mouse itself failed.

Common mistakes

Wrong battery size causes the most avoidable failures. A model that takes AA cells will not work properly with AAA batteries, even if the compartment seems to close.

  • Installing the wrong size: match AA to AA, AAA to AAA, or the exact two-cell layout shown in the compartment.
  • Reversing polarity: align the plus and minus ends with the printed marks.
  • Leaving the receiver unplugged: the USB nano receiver must stay connected for most HP 2.4 GHz mice.
  • Ignoring bent or dirty contacts: straighten a lightly bent spring and wipe corrosion with a dry cloth if needed.
  • Forcing a stuck cover: if there is no release tab, press the latch area and slide or lift only as designed.

Keep reading

Frequently asked questions

How to change battery in hp comfort grip wireless mouse

Open the Comfort Grip battery compartment only after switching the mouse off. Check the battery already installed in the mouse, then replace it with the same size. Match the polarity marks, close the shell, and confirm the receiver is still plugged in.

Why hp wireless mouse not working

After a battery swap, the usual next checks are the USB nano receiver, the battery contacts, and the power switch. Reinsert the receiver, power cycle the mouse, and inspect the springs for weak contact. If the pointer stays dead, try another USB port on the PC.