To reset a Logitech keyboard, first identify whether it uses Bluetooth, a Unifying receiver, or Easy-Switch pairing memory; most models do not have a true factory-reset button, so the reset is usually a pairing reset. A wrong sequence can leave the keyboard unpaired or stuck on the wrong device. This guide shows how to identify your model first, then follow the exact reset path and the most common failure mode for each type.
How do you identify your Logitech keyboard type?
Check the model name on the underside label, then match it to the connection method. Bluetooth-only keyboards pair through the operating system, Easy-Switch models store more than one device slot on the keyboard itself, and Unifying models use a tiny USB receiver. That difference decides whether you clear OS pairing, keyboard memory, or both.
If you are unsure, open Logitech software such as Logi Options+ and look at the connected device name. If the keyboard has numbered device keys, it is usually an Easy-Switch model. If a USB receiver is involved, treat it as a receiver workflow first, not a pure Bluetooth reset.
Likely causes when the reset fails
- Stale Bluetooth pairing is still stored on the computer, tablet, or phone.
- Easy-Switch memory still holds an old device slot.
- The Unifying receiver needs reconnection or the wrong receiver is plugged in.
- Logi Options+ or older Logitech software is still applying the old settings.
Keyboard reset matrix
This table separates a true keyboard-side reset from simple reconnection. Read the connection type first, because the same Logitech name can behave differently over Bluetooth and a receiver. On many models, the first check after a failed reset is whether the old pairing still exists on the host device.
| Keyboard family | Connection type | Exact reset steps | Expected LED behavior | Forget device in OS Bluetooth settings? | First failure-check |
|---|---|---|---|---|---|
| MX Keys | Bluetooth or Easy-Switch | Use Esc + O, Esc + O, Esc + B, then power cycle the keyboard. | Lights should flash multiple times. | Yes, if the keyboard was paired over Bluetooth. | Check that all Easy-Switch slots are not still linked to the old host. |
| K380 | Bluetooth / Easy-Switch | Hold the active Easy-Switch key until the LED blinks, then start pairing again. | Pairing LED blinks rapidly. | Yes. | Confirm the host removed the old Bluetooth entry before re-pairing. |
| K780 | Bluetooth or Unifying receiver | Bluetooth: clear the OS pairing, then re-enter pairing mode from the keyboard. Receiver: unplug and reinsert the receiver, then reconnect the keyboard. | Pairing LED blinks during Bluetooth pairing. | Yes for Bluetooth; no for a receiver-only reconnect. | Verify you are using the intended workflow, not mixing receiver and Bluetooth steps. |
| K850 | Bluetooth, Easy-Switch, or receiver | Clear the active slot or pairing, then re-pair the keyboard to the same host. | LED blinks while pairing. | Yes for Bluetooth. | Check whether the active Easy-Switch slot still points at another device. |
| K270 | Unifying receiver | Re-seat the receiver, then reconnect through Logitech’s receiver pairing flow if needed. | Connection light settles after link-up. | No. | Test the receiver in a different USB port first. |
How do you reset an MX Keys?
Use the sequence Esc + O, Esc + O, Esc + B, then power the keyboard off and back on. The lights should flash multiple times after the sequence, which is the clearest reset confirmation. If it was paired over Bluetooth, remove it from the host device first, then pair it again in Bluetooth settings.
MX Keys also uses Easy-Switch memory, so the old device can keep reconnecting unless you clear the host side and then select the correct device slot again. If the keyboard comes back on the wrong computer, the reset likely worked but the pairing target did not change.
Exact MX Keys steps
- On the computer, open Settings > Bluetooth & devices and remove the MX Keys entry.
- Press Esc + O, then repeat Esc + O, then press Esc + B.
- Power the keyboard off, wait a few seconds, then turn it back on.
- Open Bluetooth pairing again and connect the keyboard.
How do you reset a K380?
The K380 is a Bluetooth keyboard, so the practical reset path is to clear its pairing and re-enter pairing mode from the keyboard itself. Remove the keyboard from the operating system first, then hold the active Easy-Switch key until the LED blinks and pair it again. If the old host is still listed, the keyboard may reconnect to that device instead.
Say your K380 still wakes up a tablet you stopped using last week. The keyboard may be fine; the tablet still has the old Bluetooth record. Remove that record first, then repeat the pairing step on the current device.
Exact K380 steps
- Open Settings > Bluetooth & devices on Windows, System Settings > Bluetooth on Mac, or the Bluetooth list on iPad.
- Forget or remove the K380 from that list.
- Press and hold the active numbered Easy-Switch key until the LED blinks rapidly.
- Re-pair the keyboard from the Bluetooth menu.
How do you reset a K780 or K850?
Split these models by connection type first. A K780 can work through Bluetooth or through a receiver setup, so the reset path changes with the link you actually use. K850 can involve Easy-Switch or receiver troubleshooting, which means clearing the host pairing may matter more than hunting for a hidden reset button.
For both models, the common failure is a device slot that still points to the old computer. If the keyboard blinks but reconnects to the wrong host, the reset itself was not the issue; the pairing record was.
K780 Bluetooth path
- Open the Bluetooth list on the host device and remove the K780.
- Put the keyboard into pairing mode with its Bluetooth control or active Easy-Switch slot.
- Pair again from Settings > Bluetooth & devices on Windows, System Settings > Bluetooth on Mac, or Bluetooth settings on iPad.
- Turn the keyboard off and on once after pairing.
K780 receiver path
- Unplug the Unifying receiver.
- Plug it back into the same or a different USB port.
- Use the receiver pairing flow in Logitech software if the keyboard does not reconnect automatically.
- Do not treat the receiver reseat as a factory reset; it is a reconnect step.
K850 path
- Forget the K850 in the operating system if it was paired by Bluetooth.
- Use the active Easy-Switch key or pairing control to start a new connection.
- Reconnect the keyboard in Bluetooth settings or through the receiver workflow you use.
- If it fails, check whether another Easy-Switch slot still holds the old host.
What if your keyboard has no reset button?
That usually means the keyboard uses pairing memory, not a dedicated reset button. The fastest path is to clear the device from the host system, power the keyboard off and back on, then force pairing mode again with the model’s Bluetooth or Easy-Switch control. Receiver models need receiver reconnection, not a hardware reset.
A common first-timer mistake is trying to “reset” a Unifying keyboard by pulling the USB receiver and stopping there. That only disconnects the link. You still need to remove the device from software or run Logitech’s receiver pairing flow if the host keeps trying the old match.
Still not working?
Start with Logi Options+ if the keyboard is supported there. Update it, or remove and reinstall it if the pairing screen still shows the wrong device state. Then repeat the reset after a full power cycle and after forgetting the keyboard in Bluetooth settings. If it still reconnects incorrectly, test the keyboard on a second computer or tablet to separate keyboard-side trouble from host-side pairing problems.
If the keyboard works on one device but not another, the issue is usually the stale Bluetooth record, the receiver setup, or software conflict on the failing host. If it fails everywhere, the keyboard itself may need vendor support.
If that didn’t work, try this next
- Close Logi Options+ completely, then reopen it after pairing.
- On Windows, remove the device from Settings > Bluetooth & devices > Devices, then reboot.
- On Mac, remove it from System Settings > Bluetooth, then restart the Mac.
- On iPad, forget the keyboard in Bluetooth settings, then pair again.
- Try the keyboard on a second host device with the same sequence.
Frequently asked questions
How do you factory reset Logitech keyboard?
Many Logitech keyboards do not appear to have a single universal factory-reset button. The usual fix is to remove the keyboard from the host’s Bluetooth list, clear the active pairing on the keyboard with the correct model sequence, power cycle it, and pair it again. The exact steps depend on the family.
How do you reset Logitech keyboard Bluetooth?
Open the Bluetooth menu on the host device, forget the keyboard, then put the keyboard back into pairing mode. On Mac or iPad, use the Bluetooth settings screen; on Windows, use Settings > Bluetooth & devices. After that, re-pair and power cycle the keyboard once.
How do you reset Logitech keyboard without reset button?
Use the model’s pairing controls instead of looking for a pinhole. For receiver models, unplug and reinsert the receiver, then run Logitech’s pairing flow if needed. The keyboard still needs re-pairing afterward.
How do you reset Logitech keyboard K850?
Forget the K850 from the host device if it is paired by Bluetooth, then use the active Easy-Switch or pairing control to start a new connection. If you use a receiver, reconnect through that path instead. If it fails, check whether another slot still points to an old device.
How do you reset Logitech keyboard K270?
The K270 commonly uses a Unifying receiver workflow, so a practical fix is to reconnect the receiver rather than look for a factory-reset button. Re-seat the USB receiver, try another USB port, and run Logitech’s receiver pairing process if the keyboard does not return automatically.
How do you reset Logitech keyboard and mouse?
Reset them separately. Forget each device in the host’s Bluetooth settings if they use Bluetooth, then reconnect one at a time. If both use a Unifying receiver, re-seat the receiver and pair each device through the receiver software. One device can reconnect while the other still fails.