Use Logitech Options+ for many MX and productivity mice, and Logitech G HUB for Logitech G devices. Only use a dedicated firmware updater when Logitech lists one for your exact model. If the app cannot find the mouse, or the model is not supported there, stop and check the model family, receiver type, and pairing path before you force anything.

Which Logitech app should you use?

Which Logitech app should you use?
A wireless mouse sits beside a laptop on a wooden desk

Start with the app that matches the mouse family. MX, Signature, and Pebble models are commonly used with Logitech Options+, while Logitech G mice are commonly used with Logitech G HUB. If the mouse connects by Bluetooth, Unifying USB Receiver, Logi Bolt USB Receiver, or LIGHTSPEED Wireless USB Receiver, confirm the exact model support before you try an update.

What the app choice usually looks like

Mouse family Connection type Likely software to try first Update risk When to stop and troubleshoot instead
MX Bluetooth or receiver-based Logitech Options+ Low if the exact model is listed; higher if the device is paired through the wrong receiver path Stop if the mouse is not shown on the device page, or if the app offers no firmware item
Signature Bluetooth or Logi Bolt / Unifying USB Receiver Logitech Options+ Low to moderate, depending on model support Stop if the model is missing from the updater or a pairing step is still incomplete
Pebble Bluetooth, and some models may support other Logitech connectivity options Logitech Options+ Low if supported; do not assume every Pebble model has a firmware path Stop if the app shows only button setup and no firmware area
Logitech G LIGHTSPEED Wireless USB Receiver or Bluetooth on some models Logitech G HUB Moderate, because firmware and tuning options sit in the same app Stop if G HUB does not detect the device after receiver and port checks

What the connection type changes

Bluetooth means the mouse pairs directly to the computer. Receiver-based models use a USB receiver instead, which can matter during pairing and during firmware detection. Logitech lists Bluetooth, Logi Bolt USB Receiver, and Unifying USB Receiver on many mice, while Logitech G mice can use LIGHTSPEED Wireless USB Receiver.

What you’ll need

  • Your exact mouse model name from the bottom label, box, or device listing
  • The correct Logitech app already installed: Options+ for MX, Signature, and many Pebble models; G HUB for Logitech G
  • A charged mouse battery
  • A stable computer connection
  • The matching receiver if your mouse uses one
  • Enough time to keep the mouse and receiver connected until the update finishes
How to update your Logitech mouse
A firmware update tool window for Logitech devices is shown on screen

Open Logitech Options+ for MX, Signature, or Pebble models, or Logitech G HUB for Logitech G devices. Wait for the app to detect the mouse, then check the device page for a firmware or status update notice. If the app offers an update for your exact model, install it and keep the mouse and receiver connected until the process ends. If nothing appears, stop and verify support instead of clicking through the same screen again.

  1. Open Logitech Options+ or Logitech G HUB, depending on the mouse family.
  2. Connect the mouse with Bluetooth or the matching receiver, then wait for the device card to appear.
  3. Open the mouse card and check the status, firmware, or device information area.
  4. If the app shows an update, select the firmware update button and keep the mouse awake.
  5. Leave the receiver plugged into the same port and do not switch ports during the update.
  6. When the app says the update is complete, close and reopen the app once, then confirm the mouse still appears.

Suppose an MX Anywhere 3S is paired over Bluetooth, but the device card never shows firmware information. That usually means the app has not confirmed support for that model in that connection path, so the next step is to check Options+ on the same computer before trying a different mouse or receiver.

What the update screen should show

Look for a device card, status line, or firmware notice inside the app. Logitech G HUB is a configuration app for Logitech G gear on Windows and macOS, and it can be used to set DPI and assignments. MX Master 4 is described as a high-performance wireless mouse with haptic feedback and native Advanced Haptics integration on Windows 11.

Can a firmware update fix lag or disconnects?

Can a firmware update fix lag or disconnects?
Two computer mice sit beside a laptop on a desk

Yes, sometimes. A firmware update can help when the mouse has a known device-software issue, a feature support gap, or a responsiveness problem that Logitech has linked to firmware. It will not fix every lag complaint. If the real cause is pairing, battery level, USB placement, or wireless interference, firmware is not the first fix.

When firmware is a plausible fix

Use the update if the app clearly offers one for your exact mouse and the symptom matches a device-level issue such as inconsistent clicks, poor wake behavior, or a feature that the current firmware does not support well. MX Master 4, for example, may need app support for its feature set, while Pebble Mouse 2 M350s is a slim, compact Bluetooth mouse with a customizable button.

When to troubleshoot something else first

If the cursor lags only near a crowded USB setup, or the mouse drops only after moving the receiver to a rear port, the problem is more likely placement or interference. If the mouse disconnects right after a fresh battery change, check the battery contacts and pair again before chasing firmware.

What if your mouse is not listed?

Stop before you force an update. If the model is not listed in the app, the updater may not support that mouse at all, or you may be in the wrong app. For receiver models, confirm the correct Unifying or Logi Bolt pairing path before you try another pass.

  1. Check the model name against the label on the mouse and the box.
  2. Open Logitech Options+ for MX, Signature, or Pebble models; open G HUB for Logitech G devices.
  3. If the mouse uses a receiver, pair it through the matching receiver path inside the same app before looking for firmware.
  4. If the device still does not appear, try a different USB port or reconnect Bluetooth from the system Bluetooth menu.

A common first-timer mistake is assuming a wireless Logitech gaming mouse can use the same firmware update steps as a basic office model. A Signature mouse on Logi Bolt and a Logitech G mouse on LIGHTSPEED do not follow the same path, even though both may show up after pairing. Keep the app matched to the family, not to the connector alone.

What should you do before starting a Logitech mouse firmware update?

Charge the mouse, keep it close to the computer, and close other Logitech tools or mouse-mapping apps that may grab the device. If you are using a receiver, leave it plugged in. If the update is interrupted, the mouse may stop responding until you reopen the app and repair the connection.

  1. Charge the mouse until battery warnings disappear.
  2. Keep the mouse and receiver within a short range of the computer.
  3. Close other mouse apps, macro tools, and system utilities that may conflict.
  4. Confirm the mouse appears in the Logitech app before you start.
  5. Start the update only if the app explicitly offers one for your model.

If that didn’t work, try this next

  1. Restart the Logitech app first.
  2. Unplug and reinsert the receiver in a different USB port.
  3. Reboot the computer, then reconnect the mouse.
  4. Only after that, repeat the update check once.

Common mistakes

Do not confuse firmware updates with software setup. Firmware lives on the mouse itself; software settings live in Logitech Options+ or G HUB. Do not unplug the receiver or turn off the mouse mid-update. Do not assume Bluetooth, Unifying, Logi Bolt, and LIGHTSPEED all update through the same path.

  • Using the wrong app for the mouse family
  • Starting an update without checking whether the model is supported
  • Disconnecting the receiver during the update
  • Ignoring a low-battery warning
  • Forcing an update when the mouse already works normally

What if the update fails or the mouse stops responding?

First, reopen the Logitech app and check whether the mouse reconnects on its own. If not, restart the computer, replug the receiver, and pair the mouse again through the same app or system Bluetooth menu. If the model still will not appear, stop and verify support for that exact mouse before trying again.

  1. Close the Logitech app.
  2. Unplug the receiver or disconnect the Bluetooth pairing.
  3. Restart the computer.
  4. Reconnect the mouse using the matching receiver or Bluetooth path.
  5. Open the correct Logitech app and check whether the device returns.

Say your Logitech G mouse loses button mapping after an interrupted update. Open G HUB, select the device page, and check whether assignments and DPI settings still load. Then reconnect via LIGHTSPEED Wireless USB Receiver if needed. If the device never reappears, stop and use the pairing flow rather than retrying the update blindly.

Keep reading

Frequently asked questions

Why is logitech mouse lagging?

Check battery level, receiver placement, and wireless interference first. A rear USB port, a hub packed with devices, or a nearly flat battery can cause lag that looks like a firmware problem. If the app offers a model-specific firmware update, install it only after those basics are checked.

Do I need G HUB or Logitech Options+ to update my mouse firmware?

Use G HUB for Logitech G devices and Options+ for MX, Signature, and many Pebble models. If the mouse is on Bluetooth or a receiver, the exact support still depends on the model. The updater only appears after the app recognizes the device and confirms support.

How do I know if my Logitech mouse model supports firmware updates?

Look for the device in the app’s mouse card or firmware section. If the model appears and the app offers an update, it is supported in that path. If the device appears only for button setup and no firmware area exists, that model may not have a firmware update there.

Can a firmware update fix Logitech mouse lag or disconnects?

Sometimes, but only when Logitech has a device-level fix for that model. If the real issue is pairing, battery, USB placement, or wireless interference, firmware will not solve it. Treat the update as one possible fix, not the default answer for every lag complaint.

What if my Logitech mouse is not listed in the updater?

Switch to the correct app for the family, then confirm the receiver path. A Logitech G mouse may need G HUB, while an MX or Signature model may need Options+. If the mouse still is not listed after pairing and port checks, stop and verify that the model supports firmware updates at all.