If a Logitech keyboard stops responding while the mouse still works, check the keyboard’s power first, then the receiver or Bluetooth link, then OS input settings, and then Logitech software if needed. That order saves time and keeps you from swapping the wrong part. This guide shows how to isolate each subsystem fast and tells you what to fix when the keyboard fails but the mouse still moves.
Likely causes
When the mouse still works, the computer is not usually having a full input outage. The fault is more often local to the keyboard: a weak battery, a power switch left off, a bad receiver path, a broken Bluetooth pairing, or a Windows or macOS setting that affects only the keyboard profile.
Suppose a Logitech K270 mouse moves normally, but the keyboard types nothing in Windows. That pattern points away from the whole PC and toward the keyboard side of the connection. A common first-timer mistake is to swap the mouse and keyboard into different ports without checking whether the keyboard’s own battery or pairing has dropped.
| Diagnostic branch | Symptom | Exact test to run | Likely cause | Next action |
|---|---|---|---|---|
| Power or battery | No typing, no LED activity, or the keyboard wakes only briefly | Toggle the keyboard off and back on, then replace with fresh batteries or fully charge it | Low charge, wrong battery orientation, or a stuck power state | Check battery polarity, then replace batteries or recharge |
| USB receiver | Wireless keyboard fails, but other USB devices work | Plug the receiver directly into the computer, then try a different USB port | Loose dongle, hub issue, or interference near the port | Move the receiver to a direct port and avoid USB hubs |
| Bluetooth pairing | Keyboard is visible but will not type after pairing history changes | Forget the device in system settings, then pair it again | Broken Bluetooth link or stale pairing record | Remove the old entry and complete a fresh pairing |
| OS or software | Keyboard works in pre-boot screens but not in Windows or macOS | Reboot, then check USB selective suspend, drivers, firmware, or G HUB | Power-saving setting, driver issue, or Logitech software conflict | Disable the setting, update drivers, then check firmware and G HUB |
Is the keyboard out of power?
For battery-powered Logitech wireless keyboards, low charge can stop typing completely. Start here because it is the fastest fix, and it is the first step wikiHow lists for this type of problem. Also check the power switch, because some Logitech wireless and Bluetooth models simply need an off-and-on reset.
- Flip the Logitech keyboard power switch off, wait 5 seconds, then turn it back on.
- Open the battery compartment and confirm the battery orientation matches the plus and minus marks.
- Remove the batteries and replace them with fresh ones, even if the mouse battery still looks fine.
- If the keyboard is rechargeable, connect it to power and leave it for at least 10 minutes before trying again.
- Test the keyboard in a text field after the reset, not just on the desktop.
Why is my Logitech keyboard not responding when the mouse works? A dead or weak keyboard battery is one of the most common reasons, because the mouse and keyboard often have separate power states even when they share the same receiver. The keyboard can fail alone while the mouse keeps working normally.
Is the receiver or Bluetooth link failing?
If the keyboard has power but still will not type, check the wireless link next. The tiny USB receiver should be plugged directly into the computer, not into a hub or a dock, and wikiHow recommends trying a different USB port. For Bluetooth models, the fix is usually to forget the device and pair it again.
- For a USB receiver, unplug the dongle and plug it directly into a computer USB port.
- Try a second USB port on the machine, preferably one on the computer itself rather than on a hub.
- Move the receiver away from the back of the case if it is blocked by metal, a dock, or a cable bundle.
- Remove nearby interference sources such as other wireless dongles, a USB 3.0 drive sitting next to the receiver, or dense cable clutter.
- For Bluetooth keyboards, open Settings > Bluetooth and devices, remove the Logitech keyboard, and pair it again.
- Test the keyboard on another computer to see whether the same connection failure follows the device.
How do I rule out a USB receiver or Bluetooth problem? Use the fastest isolation test first: move the receiver to a direct port, then pair the keyboard again if it uses Bluetooth. If the keyboard works on another computer, the connection path on the original machine is the likelier problem, not the keyboard hardware itself.
Is Windows or Logitech blocking input?
When the keyboard works before Windows loads, but not after sign-in, the problem is usually in the OS or software layer. A reboot often clears temporary faults. On Windows, USB selective suspend can interrupt keyboard input, and Logitech drivers, Bluetooth drivers, firmware, or G HUB may also be part of the failure path.
- Restart the computer first. That applies to both Windows and Mac.
- On Windows, open Control Panel > Power Options > Change plan settings > Change advanced power settings > USB settings > USB selective suspend setting, then set it to Disabled.
- Open Device Manager and update the USB or Bluetooth driver for the keyboard’s connection path.
- Check Logitech G HUB if you are using a supported Logitech G keyboard. Open G HUB and look for device status, updates, or profile issues.
- Check for a keyboard firmware update after the basic hardware checks are done.
Should I update Logitech firmware or drivers if the mouse still works? Yes, but only after the battery, receiver, and Bluetooth checks. Firmware can fix malfunctioning behavior on supported keyboards, and driver updates can repair recognition problems in Windows even when the mouse keeps working. That sequence avoids chasing software before the connection is stable.
Still not working?
If the keyboard still fails after those checks, the next step is to separate hardware failure from computer-side failure. Test the keyboard on another device, then check whether it works in BIOS or other pre-boot screens. A keyboard that works before Windows loads but stops later usually points to settings, drivers, or Logitech software.
- Try the keyboard on another computer or tablet that supports the same connection type.
- Restart into BIOS or UEFI setup and test whether the keyboard can move through menus there.
- If it works in BIOS but not in Windows, return to USB selective suspend, driver updates, and G HUB profiles.
- If it fails on every device, contact Logitech support or replace the keyboard if it is out of warranty.
Picture a Logitech K270 that types fine in BIOS but not after the Windows desktop appears. That usually means the keyboard itself is alive, but something in Windows is interrupting recognition. In that case, a driver update or USB selective suspend change is more useful than replacing batteries again.
For wireless models, prevention is simple: keep fresh batteries in the keyboard, keep the receiver on a direct USB port, and avoid leaving the dongle behind a hub or dock where interference is more likely.
Frequently asked questions
Why is my Logitech keyboard not working?
Start with the keyboard’s power, then the connection path, then the operating system. If the mouse still works, the failure is usually device-specific rather than a full computer outage. A battery check, a power-switch reset, or a direct-port receiver test usually finds the problem faster than a broad software hunt.
Why is my Logitech wireless keyboard not working?
Wireless models most often fail because of low batteries, a bad receiver position, or a broken Bluetooth pairing. Replace the batteries with fresh ones, plug the receiver directly into the computer, or forget the Bluetooth device and pair it again from Settings > Bluetooth and devices.
What should I check first when my Logitech keyboard stops typing?
Check the battery or power state first. For battery-powered models, confirm the battery orientation and replace weak cells. Then toggle the power switch off and on, because that simple reset can clear a stuck state without touching Windows or Logitech software.
How do I fix a Logitech wireless keyboard that stopped connecting?
Use the connection path that matches the model. For USB receivers, move the dongle to a direct USB port and avoid hubs. For Bluetooth, remove the keyboard from system settings and pair it again. Then reboot the computer so Windows or macOS reloads the device profile.
Should I update Logitech firmware or drivers if the mouse still works?
Yes, but only after the basic hardware checks. Update the USB or Bluetooth driver that matches the keyboard connection path in Device Manager on Windows, then check for firmware updates for the keyboard. If you have a supported Logitech G model, open G HUB and confirm the device is detected and current.
How do I rule out a USB receiver or Bluetooth problem?
Move the receiver to a direct port and test a second port on the computer itself. For Bluetooth, forget the device, then pair it again after disconnecting. If the keyboard works on another device but not this one, the problem is likely in the original computer’s connection layer.